It is currently Sun Aug 20, 2017 1:29 pm

All times are UTC - 6 hours

Welcome to chefknivestogo

You are currently viewing our boards as a guest, which gives you limited access to view most discussions and access our other features. By joining our free community, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content, and access many other special features. In addition, registered members also see less advertisements. Registration is fast, simple, and absolutely free, so please, join our community today!

 Page 1 of 1 [ 5 posts ] 
Author Message
 Post subject: Edge Pro and Yanagi
PostPosted: Tue Aug 21, 2012 4:02 am 

Joined: Tue Aug 21, 2012 3:27 am
Posts: 6
Hello everyone,

I hope I did not miss a similar thread on this topic, but I searched as thoroughly as I could, yet being a frenchie, I may very well have.

My question is the following: is it possible to sharpen a yanagi on an EP, [b]without reprofiling the blade in the first place [/b]? I will elaborate a little on why I don't see any other solution:

The yanagi blade slowly gets narrower all the way from heel to tip. Therefore, as the spine of the blade moves along the guide of the EP, the angle of the stone with respect to the flat of the blade increases slightly. And this is not a question of keeping the blade parallel to the table, just simple math in a triangle with one edge getting shorter. Although it may not be a problem on, say, a sujihiki, where a few tenths of a degree will go unnoticed as they will result in few microns of edge width, it is a problem on my yanagi: if the stone contacts the full width of the bevel at the heel, it barely grinds the lower millimeter (sorry for the metric system^^) of the bevel at the tip.
The reason for this seems to me that the angle of the bevel with respect to the (concave yet almost) flat of the blade is constant, so the variation of the angle of the stone is of consequence when the bevel is more than half an inch wide.

I expect this problem would not arise with an usuba, which has the (almost) same blade width from heel to tip

So here are a few potential conclusions I came up with, but I'm eager to have the advice of people more skilled with yanagis and/or EP as I am:
1) Just spend a couple hours reprofiling the yanagi blade to end up with a slightly variable bevel angle that will be matched by the EP stone.
2) Keep sharpening my yanagi freehand, as I do with my Suisin Deba and my Ittosai Usuba
3) Dump the yanagi for a better one (this is a Global one, and it is far from perfect: the back is not consistently ground, resulting in a variable edge width on the back, it does not retain the edge nearly as well as the two others,...) which would not have this issue, if such a yanagi exists ?

Thanks for your feedback!


 Post subject: Re: Edge Pro and Yanagi
PostPosted: Tue Aug 21, 2012 7:36 am 

Joined: Tue May 01, 2012 3:37 pm
Posts: 595
Location: Pensacola, FL, USA
My vote is for continuing to sharpen your single-bevel knives freehand. The Edge Pro is not suitable for use on these knives.

 Post subject: Re: Edge Pro and Yanagi
PostPosted: Wed Aug 22, 2012 11:56 am 

Joined: Wed May 16, 2012 5:12 am
Posts: 61
I don't want to come off as having much expertise on the yanagi-meets-the-edge-pro question, but wanted to at least try to be helpful. I have both edge pro and a yanagi, and the two have never met. Why? I have read from several posters (who know loads more than i do on the subject of sharpening and appear to be pros at this) that one should only sharpen the yanagi by hand. Rather than me trying to parrot their logic (which I recall seemed very reasonable), you should continue to look at a few knife sites because i did read several very thoughtful posts on this subject. i would probably at least try to run those posts down before you try it, then can you make your own decision.

Again, look around a bit more, because i know i have seen discussions on this subject. hope that sort of helps.

 Post subject: Re: Edge Pro and Yanagi
PostPosted: Thu Aug 23, 2012 5:25 am 
Forum Moderator
User avatar

Joined: Sun Apr 22, 2012 12:27 pm
Posts: 749
Location: Herentals, Belgium
I've used my EP on probably a few hundred knives, but I prefer to do single bevels by hand.

You can use an EP, but you will re-profile the wide bevel and you'll grind it completely flat. I find it just as easy to do freehand and it's faster.

Michiel Vanhoudt

Belgian Sharpening
 Post subject: Re: Edge Pro and Yanagi
PostPosted: Fri Aug 24, 2012 2:03 am 

Joined: Tue Aug 21, 2012 3:27 am
Posts: 6
Right. I've taken a look at other forums, and either the bevel was ground flat, or the yanagi had a one millimeter "macrobevel" that in my opinion makes it nothing more than a bulky suji. I guess I will continue freehand, which gives good result for the moment.

I guess it just doesn't do the EP justice to explain how you can use it for single bevel knives, if it is actually mechnaically impossible for it to do a good job on these. It's such a great tool for double bevels that it should be sufficient... worse, it could cast a doubt on the other statements from EdgePro, which are indeed justified.

Thanks !

Display posts from previous:  Sort by  
 Page 1 of 1 [ 5 posts ] 

All times are UTC - 6 hours

Who is online

Users browsing this forum: No registered users and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: