It is currently Fri Sep 19, 2014 6:06 pm



Welcome
Welcome to chefknivestogo

You are currently viewing our boards as a guest, which gives you limited access to view most discussions and access our other features. By joining our free community, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content, and access many other special features. In addition, registered members also see less advertisements. Registration is fast, simple, and absolutely free, so please, join our community today!





 Page 2 of 2 [ 13 posts ]  Go to page Previous  1, 2
Author Message
 Post subject: Re: Comments Please - Stones - Polisher Final Finisher
PostPosted: Tue Mar 19, 2013 9:07 pm 
Forum Moderator
User avatar

Joined: Mon Apr 23, 2012 4:45 am
Posts: 1396
Adam seems to have a bit more of a preference towards softer stones. Michiel prefers stones a bit harder - Shaptons and, among the Naniwa stones, the 8k snow white. I find the 12k Superstone harder than the 10k. Under the scope the 12k SS does produce a finer finish, but the softness of the 10k SS does give the perception of greater refinement. These are all very valid and reasonable perspectives. The 10k and 12k SS are popular for straight razor honing as well. My preference here for straights is the 15k pro.

For a straight razor, I certainly prefer greater refinement. Shaving with a final 8k edge is IMO barbaric :) The 15k Bamboo is not as hard as the Shapton 15k and it appears to be a bit more refined, the best of both worlds, and would be my ultimate choice. But given your choice of a 12k SS, it's time to move on to compounds. So 12k is approximately a 1.5 micron edge. I'd begin by doubling it to a 0.75 micron (24k) CBN on Balsa or nanocloth. I prefer nanocloth over balsa. Following that with a quarter micron (64K) CBN on nanocloth and then a tenth micron (160k) CBN emulsion on Kangaroo as an ideal sequence. Later on as you grow accustomed to these extreme edges, you can go to a final level of refinement of 0.025 micron Polycrystalline diamond.

For finishes as coarse as quarter micron or coarser, diamond tends to produce a less comfortable edge. For grits tenth micron or finer, this effect seems to 'go away'. This is understandable, since an 0.025 micron polycrystalline diamond finish is a scratch pattern 10x finer than a quarter micron finish. For the intermediate range, I prefer CBN both for cost and effect. CBN is more expensive than monocrystalline but less expensive than polycrystalline diamond. Polycrystalline presents multiple sharp edges on a particle the same size as a monocrystalline particle so it is effectively a finer scratch pattern and because it has more sharp edges it also cuts more aggressively. For embedded applications, monocrystalline has advantages in that the particles maintain their size and structure and stay embedded longer in the typically nickel or resin like matrix holding the particles in place.

---
Ken



_________________
My Facebook Page
Ken'sCorner
Offline
 Profile  
 
 Post subject: Re: Comments Please - Stones - Polisher Final Finisher
PostPosted: Thu Mar 21, 2013 7:27 pm 

Joined: Sat Mar 09, 2013 8:02 pm
Posts: 19
Hi Ken,

Thank you for the additional details for sharpening the straight razor and suggestions. You have a tremendous amount of quality knowledge with sharpening and stones including the JNATs. I am very glad that you are sharing this wealth of knowledge with the CKTG Forum and the knife community around the world. Also, I think that capturing much of your sharpening on videos will be there for all of us and future generations. I understand that there are different opinions from time to time on stones and techniques and approaches, etc. Thats why this forum is great to hear the insights and perspectives from many experts. Ken, I think you have established a lasting legacy in the sharpening world which will continued to be referenced!

Thank you for taking time to share your wisdom with all of us!

Each time I get on this forum - I learn more and more - mainly that I am a beginner compared to all of you.

Peter


Offline
 Profile  
 
 Post subject: Re: Comments Please - Stones - Polisher Final Finisher
PostPosted: Fri Mar 22, 2013 5:50 pm 
Forum Moderator
User avatar

Joined: Mon Apr 23, 2012 4:45 am
Posts: 1396
Peter thank you for the kind words. /Blushing. I have always been a teacher of one sort or field of knowledge or another. Long ago, I learned the expression, " See on, do one, teach one". You begin learning by seeing someone do something. Then you do it. But to truly learn it you must teach it, watching another learn it to truly expose to yourself what you truly know and what you really don't yet know well enough. I get pleasure from teaching and accept that there isn't just one answer to many questions, so in a forum like this you have the opportunity to learn from many experts other than just me - and I get to learn too. Mark has provided a very fertile environment for us all to thrive in. I see newbies mature into teachers and this is one of my greatest pleasures.

---
Ken



_________________
My Facebook Page
Ken'sCorner
Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 2 of 2 [ 13 posts ]  Go to page Previous  1, 2


Who is online

Users browsing this forum: Jason B. and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


suspicion-preferred